cruise各部件參數定義說明(電動車建模)

1、5.30. Electric Machine (EM) 5.1. Vehicle (V) 5.32. Battery H (QH) 5.27. Electrical Consumer (X) 5.59. Cockpit (CO) 5.16. Single Ratio Transmission (D) 5.17. Differential (N) 5.98. Wheel / Tire (W) 5.56. Brake (B

2、) 5.48. Anti Slip Control (ASC) C:\Program Files (x86)\AVL\CRUISE\v2015\documentation\CRUISE\v2015 Outp Output ut If activated a result output for this component is made. 如果被激活了，該組件的結果將輸出。 Losses Losses Efficiency Eff

3、iciency The Efficiency has to be defined depending on speed and power (or torque). 效率必須根據轉速和功率(或扭矩)來定義 Power Loss Power Loss The Power Loss has to be defined depending on speed and power (or torque). 功率損失必須根據轉速和功率(或扭

4、矩)來定義。 Temperature Temperature Calculated Calculated The machine temperature is calculated by the component using a special thermal model. 電機的溫度是用一個特殊的熱模型來計算的。 From Data Bus From Data Bus The actual valu

5、e of the machine temperature is taken from the Data Bus and used for further calculations in the component. 電機實際溫度數值取自數據總線，并用于組件的進一步計算。 Temperature model Temperature model If activated the inverter temperat

6、ure model is separately calculated. 如果激活，逆變器溫度模型分別計算。 The inverter temperature model can only be used in combination with the power loss maps option. 逆變器溫度模型只能與功率損失圖選項結合使用。 Derated Full load Derated Full load charac

7、teristics characteristics 降低全負荷特性 If activated limited full load characteristics are activated then actual torque is set to the user-defined limit every time it exceeds this limit. 如果激活，限制全負荷負載特性被激活，那么當它超過這個極限時

8、，實際的扭矩就會 被設置為用戶定義的極限。 Current Limit Current Limit On On The actual current is set to the user-defined limit everytime it exceeds this limit. 實際的電流設置為用戶定義的極限，當每次超過這個極限的時候。 Off Off The actual current has no user-define

9、d limit. From Data Bus From Data Bus The actual current is set to the current limit from Data bus every time it exceeds this data bus limit. 當超過數據總線限值時，實際的電流被設置為數據總線的限值。 Speed Limiter Speed Limiter If activated, the

10、maximum speed is controlled by the user-defined maximum speed. 如果激活，最大速度由用戶定義的最大速度控制。 Control Variable Control Variable Load S Load Signal ignal The Electric Machine is controlled by Load Signal. The Data Bus Input &#

11、39;Load Signal' has to be connected. 電機由負載信號控制。數據總線輸入的“負載信號”必須連接。 Desired Torque Desired Torque The Electric Machine is controlled by Desired Torque. The Data Bus Input 'Desired Torque' has to be connected