傳動系統外文翻譯

1、<p>　　Transmission System</p><p>　　A Basic Parts of the transmission system</p><p>　　The transmission system applies to the components needed to transfer the drive from the engine to the r

2、oad wheels. The main components and their purposes are</p><p>　　(1) Clutch --- to disengage the drive</p><p>　　--- to provide a smooth take-up of the drive</p><p>　　(2) Gearbox

3、 --- to increase the torque applied to the driving road wheels</p><p>　　--- to enable the engine to operate within a given range of speed irrespective of the vehicle speed</p><p>　　--- to give

4、reverse motion of the vehicle</p><p>　　--- to provide a neutral position so that the engine can run without moving the vehicle</p><p>　　(3) Final drive --- to turn the drive through 90°<

5、;/p><p>　　--- to reduce the speed of the drive by a set amount to match the engine to the vehicle</p><p>　　(4) Differential --- to allow the inner driving road wheel to rotate slower than the outer

6、 wheel when the vehicle is cornering, whilst it ensures that a drive is applied equally to both wheels. </p><p>　　B Clutch and Clutch Service</p><p>　　In order to transmit the power of the

7、engine to the road wheels of a car, a friction clutch and a change-speed gearbox are normally employed. The former is necessary in order to enable the drive to be taken up gradually and smoothly, while the latter provide

8、s different ratios of speed reduction from the engine to the wheels, to suit the particular conditions of running,</p><p>　　A clutch performs two tasks:</p><p>　　(1) it disengages the engine fr

9、om the gearbox to allow for gear changing.</p><p>　　(2) it is a means for gradually engaging the engine to the driving wheels, when a vehicle is to be moved from rest the clutch must engage a stationary gea

10、rbox shaft with the engine; this must be rotating at a high speed to provide sufficient power or else the load will be too great and the engine will start (come to test).</p><p>　　C Clutch Action </p>

11、<p>　　To start the engine, the driver must depress the clutch pedal. This disengages the gearbox from the engine. To move the car, the driver must reengage the gearbox to the engine. However, the engagement of the

12、 parts must be gradual. An engine at idle develops little power. If the two parts were connected too quickly, the engine would stall. The load must be applied gradually to operate the car smoothly.</p><p>　　

13、A driver depresses the clutch pedal to shift the gears inside the gearbox. After the driver releases the clutch pedal, the clutch must act as solid coupling device. It must transmit all engine power to the gearbox, witho

14、ut slipping.</p><p>　　The clutch mechanism include three basic parts: driving member, driven member, operating members.</p><p>　　The driving member</p><p>　　The driving member consi

15、sts of two parts: the flywheel and the pressure plate. The flywheel is bolted directly to the engine crankshaft and rotates when the crankshaft turns. The pressure plate is bolted to the flywheel. The result is that both

16、 flywheel and pressure plate rotate together.</p><p>　　The driven member </p><p>　　The driven member, or clutch disc, is located between the flywheel and pressure plate. The disc has a splined h

17、ub that locks to the splined input shaft on the gearbox .Any rotation of the clutch disc turns the input shaft .Likewise, any motion of the input shaft moves the clutch disc. The splines allow the clutch disc to move for

18、ward and backward on the shaft as it engages and disengages.</p><p>　　The inner part of the clutch disc, called the hub flange, has a number of small coil springs. These springs are called torsional springs.

19、 They let the middle part of the clutch disc turn slightly on the hub. Thus, the springs absorb the torsional vibrations of the crankshaft. When the springs have compressed completely, the clutch moves back until the spr

20、ings relax. In other words, the clutch absorbs these engine vibrations, preventing the vibrations from going through the drive train.</p><p>　　Operating Members</p><p>　　These are the parts that

21、 release pressure from the clutch disc. The operating members consist of the clutch pedal, clutch return spring, clutch linkage, clutch fork, and throwout bearing. The clutch linkage includes the clutch pedal and a mecha

22、nical or hydraulic system to move the other operating members.</p><p>　　When the clutch pedal is depressed, the clutch linkage operates the clutch fork .The clutch fork, or release fork, moves the throwout b

23、earing against the pressure plate release levers. These levers then compress springs that normally hold the clutch disc tightly against the flywheel.</p><p>　　At this point, the torque of the engine cannot t

24、urn the gearbox input shaft. The gears in the gearbox may be shifted or the vehicle can be brought to a full stop.</p><p>　　When the clutch pedal is released, the pressure plate forces the clutch disc agains

25、t the flywheel. The clutch return spring helps raise the pedal.</p><p>　　D Clutch Service </p><p>　　The major parts of the clutch assembly need no maintenance or lubrication during normal servi

26、ce. However, all linkage parts need lubrication at points of contact. The linkage itself must be adjusted to prevent wear of the clutch disc.</p><p>　　Free-play Adjustment</p><p>　　You can make

27、only one adjustment on the clutch linkage —the free-play adjustment. Free play is the allowable space between the throwout bearing and the pressure plate release levers. This space is important because it prevents pressu

28、re on the levers that could keep the clutch from engaging fully. In other words, the throwout bearing must be slightly away from the pressure plate levers so that the bearing applies no pressure on the levers. On the oth

29、er hand, there must not be too much free play b</p><p>　　The free play allows some motion at the beginning of the clutch pedal travel, before the pedal meets resistance. Since the distance varies with the ty

30、pe of pressure plate, check the service manual. Usually, free play should be about 20 to 25mm.</p><p>　　Free play can be adjusted at some point where the clutch linkage consists of threaded rods with locknut

31、s. The rod closest to the clutch fork is the most common adjustment point. Begin by locating the rod and locknut beneath the vehicle. Then determine which way to turn the adjustment nuts to get the correct free play at t

32、he pedal. You can get a rough estimate of free play by moving the clutch fork to see if it still has some movement. The best way to make the adjustment is to loosen the locknut </p><p>　　Check the free-play

33、adjustment every six months and make any adjustment. Clutches need adjustment that often, since free play decreases slightly as the clutch disc wears. However, the need for frequent adjustments means a problem in the clu

34、tch mechanism itself.</p><p>　　There must be free play between the throwout bearing and pressure plate release levers. Problems can result from “riding the clutch”. A driver who rests one foot on the clutch

35、pedal causes the throwout bearing to rub against the clutch release levers. As a result, the throwout bearing becomes worn quickly. Also, the clutch disc may wear out due to slippage because the parts are not fully engag

36、ed.</p><p>　　Clutch Faults</p><p>　　The following are the main faults:</p><p>　　Slip — failure of the surface to grip resulting in the driven plate revolving slower than the engine

37、flywheel : Clutch gets hot and emits an odor.</p><p>　　Spin or drag — failure of the plates to separate resulting in noise from the gearbox when selecting a gear: most noticeable when the vehicle is stationa

38、ry.</p><p>　　Judder — a vibration which occurs when the clutch is being engaged , i.e. when the vehicle is stationary.</p><p>　　Fierceness — sudden departure of the vehicle even though the pedal

39、 is being released gradually.</p><p>　　E The Clutches（supplementary contract）</p><p>　　A clutch is a friction device used to connect and disconnect a driving force from a driven member. In auto

40、motive applications, it is used in conjunction with an engine flywheel to provide smooth engagement and disengagement of the engine and manual transmission.</p><p>　　Since an internal combustion engine devel

41、ops little power or torque at low rpm, it must gain speed before it will move the vehicle. However, if a rapidly rotating engine is suddenly connected to the drive line of a stationary vehicle, a violent shock will resul

42、t.</p><p>　　So gradual application of load, along with some slowing of engine speed , is needed to provide reasonable and comfortable starts. In vehicles equipped with a manual transmission, this is accompli

43、shed by means of a mechanical clutch.</p><p>　　The clutch utilizes friction for its operation. The main parts of the clutch are a pressure plate, and a driven disk. The pressure plate is coupled with the fly

44、wheel, while the driven disk is fitted to the disk by the springs so that the torque is transmitted owing to friction forces from the engine to the input shaft of the transmission. Smooth engagement is ensured by slippin

45、g of the disk before a full pressure is applied.</p><p>　　The automobiles are equipped with a dry spring-loaded clutch. The clutch is termed “dry” because the surfaces of the pressure plate and driven disks

46、are dry in contrast to oil-bath clutches in which the plate and disks operate in a bath of oil. It is called “springloaded” because the pressure plate and the driven disk are always pressed to each other by springs and a

47、re released only for a time to shift gears or to brake the automobile.</p><p>　　In addition to the plate and disk, the clutch includes a cover, release levers, a release yoke, pressure springs and a control

48、linkage. The clutch cover is a steel stamping bolted to the flywheel. The release levers are secured inside the cover on the supporting bolts. The outer ends of the release levers are articulated to the pressure plate. S

49、uch a construction allows the pressure plate to approach the cover or move away from it, all the time rotating with the cover or move away from it, all t</p><p>　　The springs are installed with the aid of pr

50、ojections and sockets provided on the cover and pressure plate. The pressure plate sockets have thermal-insulation gaskets for protecting the springs against overheating.</p><p>　　The clutch release mechanis

51、m can be operated either mechanically or hydraulically. The mechanically-operated release mechanism consists of a pedal, a return spring, a shaft with lever, a rod m release yoke lever, a release yoke, a release ball bea

52、ring with support and a clutch release spring. When the clutch pedal is depressed, the rod and shaft with yoke shift the release bearing and support assembly. The release bearing presses the inner ends of the release lev

53、ers, the pressure plate is moved </p><p>　　The clutch hydraulically-operated release mechanism consists of a clutch pedal , clutch release spring , a main cylinder , a pneumatic booster, pipelines and hoses

54、and a lever of the clutch release yoke shaft. Time main cylinder accommodates a piston with a cup. The pneumatic booster serves to decrease the pedal force required disengage the clutch. The booster includes two housings

55、 with the servo diaphragm clamped in between. The housing accommodates pneumatic, hydraulic and servo plungers. When</p><p>　　The servo arrangement is intended for automatic change of the air pressure in the

56、 pneumatic cylinder proportionally to the force applied to the pedal. The plunger moves with the diaphragm, the outlet valve closes and the inlet valve opens thus admitting the compressed air to the pneumatic plunger pis

57、ton. The forces created by the pneumatic and hydraulic plungers are added together and are applied through the push rod to the release yoke shaft lever; the lever turns the shaft and the release yoke</p><p>

58、　　Automatic clutches were used in certain U.S. and European cars. American Motors’ “E-Stick” clutch eliminated the need for physical operation of the clutch system called “Hydrak”, which consisted of a fluid flywheel con

59、nected to a single, dry disk clutch.</p><p>　　In the “E-Stick” set up, the pressure plate levers “engage” the clutch disk rather than “release” them. Also, the clutch remains disengaged until a servo unit is

60、 applied by oil pressure when the shift lever is placed “in gear” with the engine running.</p><p>　　The “Hydrak” unit also begins operation when the lever is “in gear”. This activates a booster unit, which d

61、isengages the clutch disk. The hydraulic clutch parts are bridged over by a free-wheel unit, which goes into action when the speed of the rear wheel is higher than the speed of the engine. A special device controls engag

62、ement of the mechanical clutch, depending on whether the rear axle is in traction or is pushed by car momentum.</p><p>　　A more-or-les unusual clutch pressure plate set-up is used on late model Chrysler and

63、American Motors cars. Called a semi-centrifugal clutch, the pressure plate has six cylindrical rollers which move outward under centrifugal force until they contact the cover. As engine speed increases, the rollers wedge

64、 themselves between the pressure plate and cover so that the faster the clutch rotates, the greater the pressure exerted on the pressure plate and disk.</p><p><b>　　傳動系統</b></p><p>　

65、　A 基本傳動系統的組成部份</p><p>　　傳動系統是將發動機動力轉移到驅動輪的結構。主要的結構和目的是：</p><p>　　(1)離合器 --- 分離驅動；</p><p>　　--- 平順的接合驅動；</p><p>　　(2)變速器 --- 增加提供給驅動輪的轉矩；</p><p>　　--

66、- 使發動機能夠在給定的速度范圍里面運轉而不考慮的車速；</p><p>　　--- 使車輛的作倒退運動；</p><p>　　--- 提供一個齒輪的空檔以便發動機能不需要移動車輛就運轉；</p><p>　　(3)減速器 --- 使驅動轉向90 °；</p><p>　　--- 減少一定的驅動轉速并增大輸入轉矩；</p

67、><p>　　(4) 差速器 --- 當車輛轉彎行駛時允許內側驅動輪比外側驅動輪慢，同時驅動相等地作用于兩輪。 </p><p>　　B 離合器和離合器功用</p><p>　　為了要將發動機動力傳遞到汽車驅動輪，通常使用磨擦離合器和變速器的組合。前者是為了要逐漸地而且平順地接合并傳遞驅動 , 這是必需的，同時后者按不同比率減少兩輪轉速以適合特殊駕駛情況

68、。</p><p>　　離合器運行的二個作用：</p><p>　　(1) 它將發動機與變速器分離使其換檔；</p><p>　　(2) 它可以解釋為逐漸的接合驅動車輪與發動機 ；離合器必須以高速的轉動來產生足夠的動力，否則會因負荷過大，導致發動機熄火。 (進入靜止?fàn)顟B(tài))</p><p>　　C 離合器工作原理</p>&

69、lt;p>　　為了啟動發動機，駕駛員首先得踩下離合器踏板，使發動機與變速器分離。 為了使汽車能夠行駛，駕駛員必須再接合發動機與變速器。然而，這種接合得是逐漸進行的。發動機在不工作狀態時只能產生極小的動力。如果二個部份連接太快，發動機將會熄火。同時負荷必須被逐漸地加載才可以平順地駕駛汽車。</p><p>　　駕駛員踩下離合器踏板并掛檔變速器。在駕駛員松開離合器踏板之后，離合器成為一個結合裝置，將所有的發動機

70、力量傳遞到變速器，而不會打滑。</p><p>　　離合器機構包括三個基本的部份：主動部分，從動部分，操縱機構。</p><p><b>　　●主動部分</b></p><p>　　主動部分分為兩個部份: 飛輪和壓力盤。飛輪直接地被閂在發動機的傳動軸上并且隨之一起轉動。壓力盤被閂在飛輪端面上與飛輪一起轉動。</p><p&

71、gt;<b>　　●從動部分</b></p><p>　　從動部分，或離合器盤，位于飛輪和壓力盤之間。離合器盤上有一個花鍵轂用來扣在變速器上與從動軸連接。離合器盤的任何轉動都將帶動從動軸轉動，同樣地，從動軸的任何運動都將傳遞到離合器盤。從動盤在從動軸上的前后移動、分離嚙合通過滑動花鍵得以實現。</p><p>　　離合器盤的內部，叫做法蘭盤轂，有若干的小螺旋彈簧。這

72、些彈簧叫做扭力彈簧。它們讓離合器盤的中央部份在轂上些微地轉動，因此彈簧吸收傳動軸的扭轉振動。當彈簧完全壓縮時，離合器壓回到原始位置，直到彈簧松開。換句話說，離合器吸收這些發動機振動，防止振動影響到驅動齒輪</p><p><b>　　● 操縱機構</b></p><p>　　這些部份是用來釋放離合器盤壓力。操縱機構包括有離合器踏板，離合器回位彈簧，離合器聯動裝置，分離

73、叉和分離軸承。離合器聯動裝置包括離合器踏板和機械的或液壓系統用來聯動另外的操縱機構。</p><p>　　當離合器踏板被踩下的時候，離合器聯動裝置操縱著分離叉。分離叉，或者叫釋放叉，使分離軸承反向于壓力盤的分離杠桿移動。然后這些杠桿壓縮彈簧將飛輪和離合器盤緊緊地?fù)伍_。此時，發動機的轉矩還不能夠帶動變速器傳動軸。變速器檔位可能會因此加高或者導致車輛停止。</p><p>　　當離合器踏板被松

74、開的時候，壓力盤強制性的將飛輪與離合器盤分開。在離合器回位彈簧的幫助下踏板逐漸的升起。</p><p><b>　　D 離合器功用</b></p><p>　　離合器的主要部份在正常的服務期間不需要維護或者是潤滑。然而，所有的聯動裝置部份在接點處是需要潤滑的。聯動裝置本身需要一定的調整從而避免發生與離合器盤的磨損。</p><p><b

75、>　　●自由行程調整</b></p><p>　　你只能在離合器聯動裝置上作一個調整——自由行程的調整。自由行程是存在于離合器盤分離杠桿和分離軸承中允許的空間里的一段行程。這個空間是非常重要的，因?yàn)樗艿种聘軛U上的壓力從而組織離合器的嚙合。換句話說，分離軸承些微地離開壓力盤杠桿使軸承不產生作用于杠桿的壓力。另一方面，在軸承和杠桿之間又不能有太多的自由行程。如果有太多的間隙，即使當駕駛員將離合器

76、踏板踩死，離合器也不能夠完全的起到分離作用。在大部份的情形下，你應該在離合器踏板上測量自由行程，而不是在外殼。</p><p>　　在踏板遇到阻力之前，在剛踩下踏板的時候，自由行程允許一些移動發生。當距離隨著壓力盤的類型的改變而改變時，核對服務手冊來確定自由行程。通常自由行程應該是大約 20 到 25 毫米。</p><p>　　在由穿杠和鎖緊螺母組成的離合器聯動裝置的地方自由行程可以被調

77、整。最接近分離叉的竿是最常用的調整點。從在車輛之下尋找竿和鎖緊螺母的位置開始。然后決定選一種調整螺母的方法來獲得正確的踏板自由行程。如果它仍然有一些移動，你能通過移動分離叉來粗糙估計一個自由行程。調整的最好方式是松開鎖緊螺母并且旋轉螺帽。然后在踏板上核查自由行程。繼續這樣調整下去，直到你獲得正確的自由行程。當自由行程調整到制造廠的規格時，勒緊鎖緊螺母。</p><p>　　每六個月檢查自由行程并且作一些調整。離合

78、器需要時常調整，因?yàn)樽杂尚谐虝?huì)些微地減少比如與離合器盤的磨損。然而，頻繁的調整那就意味著離合器機構本身已經出現問題了。</p><p>　　在分離軸承和壓力盤分離杠桿之間一定有自由行程。而毛病可能起因于對離合器的“消遣”。駕駛員將一支腳擱在離合器踏板上使分離軸承與離合器分離杠桿產生摩擦。如此結果，分離軸承磨損的越來越快。同時由于部份裝置沒有完全嚙合，因此離合器盤也因?yàn)榛瑒?dòng)而被磨損。</p><

79、p><b>　　離合器故障</b></p><p>　　下列各項是主要的故障:</p><p>　　打滑 ——表面附者不充分造成從動片回轉的比發動機飛輪更慢：離合器很熱而且發出氣味。</p><p>　　自轉或咬死——當換檔時轉盤之間分離失敗造成變速器的噪音：其中發生最多的是在汽車不動的時候。</p><p>　　

80、顫抖——振動發生在離合器剛接合的時候，也就是當車輛不動的時候。</p><p>　　猛烈——車輛的突然啟動即使踏板正逐漸松開。</p><p>　　E 離合器綜述（補充說明）</p><p>　　離合器是一個用來連接和斷開發動機驅動力的磨擦裝置。在汽車的應用中，它和發動機飛輪組合在一起被用于平順地接合和斷開發動機與變速器之間的動力傳遞。</p>&l

81、t;p>　　因?yàn)閮?nèi)燃機在低轉速時產生的動力或轉矩很小，如果要開動車輛，就一定得增加轉速。然而，如果一臺快速轉動的發動機動力突然和車輛驅動輪連接在一起，那么車輛肯定會產生振動。</p><p>　　要讓汽車有一個合理和舒服的啟動，就必須給發動機逐漸地加載。同時發動機轉速也要逐漸減慢。車輛需要能夠?qū)崿F(xiàn)手動變速裝置，機械式離合器就能達到這個目的。</p><p>　　離合器的工作過程就是摩

82、擦的利用過程。離合器的主要部分是一個壓盤和一個從動盤。壓力盤與飛輪連接，從動盤裝在變速器的動力輸入軸上，壓盤被緊緊壓在從動盤上。這樣，由于摩擦力的存在，從發動機發出的扭矩經過變速器的傳遞而被傳送出來。通過兩個盤的相互摩擦滑轉，直到兩個盤之間的壓力扭矩最大時，動力才被平緩地傳遞出來。</p><p>　　汽車上裝備有一個干式緊壓彈簧離合器。如果壓力盤和從動盤的表面是干的，那么該離合器被稱為干式。相對的，還有一種離合

83、器稱為油浴式離合器，顧名思義此離合器的壓盤和從動盤在工作時是浸在油中。這種離合器之所以叫做緊壓彈簧離合器是因?yàn)閴毫ΡP和從動盤除了在換擋和剎車時是分開之外，總是被彈簧緊緊壓在一起。</p><p>　　除了壓盤和從動盤之外，離合器包括離合器蓋、分離杠桿、分離叉、緊壓彈簧、控制桿系。離合器蓋是一個鋼制沖件，用螺栓連接在飛輪上。分離杠桿被縛在離合器蓋的螺栓上。分離杠桿的外端連接在壓力盤上。這樣的構造使得壓力盤既能接近又

84、能遠離離合器蓋并且始終同飛輪一起轉動。而沿壓盤和離合器蓋之間的圓周均勻分布的彈簧夾住壓盤與飛輪之間的從動盤。</p><p>　　彈簧安裝在離合器蓋和壓力盤上的凸出物和承座上。為了保護彈簧免于過熱受損，在壓力盤承座上設有絕熱墊圈。</p><p>　　離合器分離裝置可以是機械式的也可以是液壓式的。機械式分離裝置由一個踏板，回位彈簧、杠桿、竿、分離叉杠桿、分離叉、分離球軸承和一個離合器分離彈

85、簧組成。當離合器踏板被踩下時，竿和分離叉軸承將扮演起支持作用的分離球軸承的角色。分離軸承壓住分離杠桿的內端，于是壓力盤和從動盤分分開，同時離合器也被分開。踏板被松開的時候，由于復位彈簧的作用分離軸承再次起到支承作用，分離杠桿分離，于是壓盤被彈簧推向飛輪將從動盤夾住，離合器又再次的接合起來。</p><p>　　液壓式離合器由離合器踏板、分離彈簧、汽缸、空氣增壓器、管道和軟管、和離合器分離叉杠桿組成。汽缸用一碗狀物

86、體調整活塞，空氣增壓器用來在離合器分離時減少踏板的阻力。增壓器由兩個有伺服隔膜夾在中間的外殼組成。這個外殼調整其中的氣體、液體和伺服柱塞。當離合器踏板被踩下時，活塞的壓力通過管道傳遞到增壓器的液體和伺服柱塞上。</p><p>　　伺服裝置可以自動調整汽缸里的氣壓以使踩踏板的力度適宜。柱塞和隔膜一同移動時，出口閥門關閉，進口閥打開，空氣進入空氣壓縮柱塞內被壓縮。由壓縮空氣和壓縮液體產生的力量將分離棒推向分離叉軸承

87、杠桿； 杠桿牽動軸和分離叉，于是離合器分離。松開踏板，出口閥門打開，入口閥門關閉，此時彈簧使活塞移動恢復了柱塞原始位置，空氣從汽缸中排出。</p><p>　　在美國和歐洲的汽車上裝有自動離合器。美國發動機“E-Stick”的離合器就不需要踩踏板。一個德國汽車制造商設計了“Hydrak”的自動離合器系統，它由液力偶合器和單片式離合器組成。</p><p>　　在“E-Stick”裝置中，

88、壓力盤的杠桿是用來連接而不是分離離合器盤的。 同時，換檔杠桿在檔位中被放置在發動機工作位置時，伺服機構在油壓的作用下使離合器分離。</p><p>　　當換檔杠桿接入某檔位時，“Hydrak”也開始運行。而后增壓機構脫離離合器盤，液壓離合器被一個自由飛輪取代。當車輪的轉速比發動機的轉速更高的時候，自由飛輪開始工作。一個特別的機械裝置根據后車橋是否被汽車動力推動來控制離合器的銜合。</p><p