廣州數控980t車削系統說明書

1、GSK980TGSK980T使用手冊使用手冊前言1.1簡介........................................................................11.2型號意義....................................................................11.3型譜.....................................

2、...................................12.1編程概要....................................................................22.1.1軸定義................................................................22.1.2機械原點..........................

3、....................................22.1.3編程坐標..............................................................22.1.4坐標的單位及范圍......................................................32.1.5初態模態..................................

4、...........................32.1.6加工程序的開頭........................................................32.1.7加工程序的結束........................................................32.1.8插補功能（參照G功能）......................................

5、..........32.1.9進給功能..............................................................52.1.10加工坐標系...........................................................52.1.11切削速度—主軸功能...................................................

6、62.1.12各種加工時選用的刀具—刀具功能.......................................72.1.13各種功能操作指令—輔助功能...........................................72.1.14程序的構成...........................................................82.1.15刀具補償功能............

7、.............................................92.1.16刀具移動的范圍—行程校驗.............................................92.2控制軸.....................................................................102.2.1控制軸數........................

8、.....................................102.2.2設定單位.............................................................102.2.3最大行程.............................................................102.3G功能...............................

9、......................................112.3.1定位(G00)............................................................122.3.2直線插補(G01)........................................................132.3.3圓弧插補(G02G03).................

10、..................................132.3.4切螺紋(G32)..........................................................162.3.5自動返回機械原點(G28)................................................192.3.6暫停(G04)...............................

11、.............................192.3.7坐標系設定(G50)......................................................192.3.8每分進給(G98).......................................................202.3.9每轉進給(G99).................................

12、......................202.3.10恒線速控制(G96G97)................................................212.3.11單一型固定循環(G90G92G94).......................................242.3.12復合型車削固定循環(G70～G76)......................................

13、..312.3.13復合型固定循環(G70～G76)的注意事項..................................412.4主軸功能(S功能)...........................................................422.4.1主軸速度指令.........................................................422.5刀具功能...

14、................................................................432.5.1換刀過程.............................................................432.5.2換刀相關參數.........................................................442.6輔助功能.....

15、..............................................................442.6.1輔助功能(M功能).....................................................45GSK980TGSK980T使用手冊使用手冊前言3.3.2自動運轉的啟動...................................................

16、....753.3.3自動運轉的執行.......................................................753.3.4自動運轉的停止.......................................................763.3.5自動運轉中冷卻液控制.................................................763.4試運轉....

17、.................................................................773.4.1全軸機床鎖住.........................................................773.4.2輔助功能鎖住.........................................................773.4.3進給速度倍率..

18、.......................................................773.4.4快速進給倍率.........................................................773.4.5空運轉...............................................................783.4.6進給保持后或者停止后的再啟動.

19、........................................783.4.7單程序段.............................................................783.5安全操作...................................................................803.5.1急停(EMERGENCYSTOP)........

20、.........................................803.5.2超程.................................................................803.6報警處理...................................................................803.7程序存儲、編輯.................

21、............................................803.7.1程序存儲、編輯操作前的準備...........................................803.7.2把程序存入存儲器中...................................................813.7.3程序號檢索..................................

22、.........................813.7.4程序的刪除...........................................................813.7.5刪除全部程序.........................................................823.7.6程序的輸出..........................................

23、.................823.7.7全部程序的輸出.......................................................823.7.8順序號檢索...........................................................823.7.9字的插入、修改、刪除..............................................

24、...832.7.10存儲程序的個數......................................................863.7.11存儲容量............................................................873.8數據的顯示、設定...........................................................873.

25、8.1補償量...............................................................873.8.2設置參數的設定.......................................................883.8.3用戶宏變量的顯示及設定...............................................893.8.4參數........

26、.........................................................903.8.5診斷.................................................................913.9顯示.......................................................................933.9.1狀態顯示

27、.............................................................933.9.2鍵入數據顯示.........................................................933.9.3程序號、順序號的顯示.................................................933.9.4程序存儲器使用量的顯示.....

28、..........................................943.9.5指令值的顯示([程序]鍵)...............................................943.9.6現在位置的顯示([位置]鍵).............................................953.9.7加工時間、零件數顯示............................

29、.....................963.9.8報警顯示([報警]鍵)...................................................963.9.9液晶畫面亮度調整.....................................................973.10軟鍵盤機床面板.................................................