經典單片機編程100例

1、組織組織我們就是要共享我們就是要共享1目錄目錄目錄...........................................................................................................1函數的使用和熟悉...............................................................................

2、....3實例3：用單片機控制第一個燈亮........................................................3實例4：用單片機控制一個燈閃爍：認識單片機的工作頻率.............4實例5：將P1口狀態分別送入P0、P2、P3口：認識IO口的引腳功能.....................................................................

3、......................................4實例6：使用P3口流水點亮8位LED...................................................5實例7：通過對P3口地址的操作流水點亮8位LED...........................6實例8：用不同數據類型控制燈閃爍時間.........................................

4、....7實例9：用P0口、P1口分別顯示加法和減法運算結果.....................8實例10：用P0、P1口顯示乘法運算結果............................................8實例11：用P1、P0口顯示除法運算結果............................................9實例12：用自增運算控制P0口8位LED流水花樣..............

5、..............9實例13：用P0口顯示邏輯“與“運算結果...........................................10實例14：用P0口顯示條件運算結果..................................................10實例15：用P0口顯示按位“異或“運算結果.......................................10實例16：用P0顯

6、示左移運算結果......................................................10實例17：“萬能邏輯電路“實驗“.........................................................11實例18：用右移運算流水點亮P1口8位LED...................................11組織組織我們就是要共享我們就是要共享3實例41

7、：宏定義應用舉例3.................................................................28中斷、定時器.........................................................................................29實例42：用定時器T0查詢方式P2口8位控制LED閃爍.................29實

8、例43：用定時器T1查詢方式控制單片機發出1KHz音頻.............29實例44：將計數器T0計數的結果送P1口8位LED顯示.................30實例45：用定時器T0的中斷控制1位LED閃爍...............................31實例46：用定時器T0的中斷實現長時間定時...................................31實例47：用定時器T1中斷控制兩個L

9、ED以不同周期閃爍...............32實例48：用計數器T1的中斷控制蜂鳴器發出1KHz音頻.................33實例49：用定時器T0的中斷實現“渴望“主題曲的播放....................34實例501：輸出50個矩形脈沖...........................................................37實例502：計數器T0統計外部脈沖數......

10、.........................................37實例512：定時器T0的模式2測量正脈沖寬度...............................38實例52：用定時器T0控制輸出高低寬度不同的矩形波...................39實例53：用外中斷0的中斷方式進行數據采集.................................40實例541：輸出負脈寬為200微秒的方波

11、.........................................40實例542：測量負脈沖寬度.................................................................41實例55：方式0控制流水燈循環點亮................................................42實例561：數據發送程序..................

12、...................................................43實例562：數據接收程序.....................................................................44實例571：數據發送程序.....................................................................45實