數字時鐘外文翻譯

1、<p><b>　　外文資料翻譯</b></p><p>　　L ED using digital tube digital display its high-brightness, indicating the advantages of intuitive intelligence is widely used in areas such as equipment and ho

2、usehold appliances. AT89C52This article describes a single-chip microcomputer as the core, to a total of anode high-brightness LED L ED as a display composed of seven figures show that the practical design of multi-funct

3、ion electronic clocks, the clock shows a week, hour, minute, second, it can be switched to year, month, day showed that</p><p>　　Clock circuit is the heart of the computer, which controls the rhythm of the w

4、ork of the computer is through the completion of complex sequential circuits function in different directions.</p><p>　　Clock, since it was invented that day on, people's lives has become an indispensabl

5、e tool, especially in this era of efficient, the clock is in the human production and living, learning and other fields is widely. However, with the passage of time, people not only to the requirements of the clock is ge

6、tting higher and higher precision, and functional requirements for the clock more and more, the clock has not only a tool used to display time, in many practical applications It also needs to be ab</p><p>　　

7、With the development of human civilization, science and technology, there is the request of the clock continues to improve. Clock has not only seen as a tool to display the time, in many practical applications also need

8、to be able to achieve more other functions. High-precision, multifunction, small size, low power consumption, is the development trend of the modern clock. In this trend, digital clock, multifunction clock has become the

9、 modern design of the production of research-led direction. </p><p>　　The design is based on the principle of single-chip technology to chip AT89C52single-chip microcomputer as the core controller, through t

10、he production of hardware and software procedures for the preparation, design to produce a multi-functional digital clock system. The clock system mainly by clock module, alarm module, the ambient temperature detection m

11、odule, liquid crystal display module, control module and the keyboard signal prompted module. System is simple and clear user interface that ca</p><p>　　Clock design is no theory of discrete logic, programma

12、ble logic, or using full-custom silicon devices of any digital design, in order to successfully operate and reliable clock is crucial. Poor design of the clock in the limits of temperature, voltage deviation or the manuf

13、acturing process will result in the case wrong, and debugging difficult, spending a lot. In the design of FPGA / CPLD clock when several types of commonly used. Clock can be divided into the following four types: global

14、clock,</p><p>　　No matter what methods are the real circuit clock tree can not achieve the ideal assumption that the clock, so we must be based on an ideal clock, the clock real work to build a model to anal

15、yze the circuit, so as to make the circuit performance and the practical work as expected . Clock in the actual model, we have to consider the spread of clock-tree skew, vertical jump and absolute bias and other uncertai

16、nties. </p><p>　　To register, the clock was working along the arrival of the data terminal when it should have been stable, so as to ensure that the work along the sampling clock to the accuracy of the data,

17、 this data preparation time that we call set-up time (setup time). Data should also be working along the clock to maintain over a period of time, this period of time known as the hold time (hold time). </p><p&

18、gt;　　Global clock for a design project, the global clock (or clock synchronous) is the simplest and most predictable clock. In the PLD / FPGA design of the clock the best options are: by a dedicated global clock input pi

19、ns of a single master clock-driven clock design projects to each flip-flop. As long as possible should be used in the design of global clock projects. PLD / FPGA has a dedicated global clock pins, the device is directly

20、connected to each register. Global clock to provide such a device</p><p>　　Clock-gated in many applications, the entire design of the overall use of external clock is not possible or practical. With the prod

21、uct of PLD logic array clock (that is, the clock is generated by the logic), to allow arbitrary function alone all trigger clock. However, when you use the array clock, the clock should be carefully analyzed the function

22、, in order to avoid glitches. </p><p>　　Usually constitute the array clock clock-gated. Clock gating often interface with the microprocessor, and used the address to write to control the pulse line. However,

23、 when using combination of flip-flop when the clock function, usually there is a clock-gated. If the following conditions, such as clock gating can be as reliable as global clock work: </p><p>　　Drive the cl

24、ock logic must contain only one "and" the door or a "or" gate. If any additional work in some state of logic, the competition will be the burr. </p><p>　　A logic gate input as the actual

25、clock, and the logic gate must be of all other input as the address or control lines, in relation to their compliance with the establishment and maintenance of clock time bound. </p><p>　　Multi-level logic g

26、enerated clock when the clock-gating logic of the combination of more than one (or more than the individual "and" doors or "or" gate), the evidence of the reliability of the design of the project has

27、become very difficult. Even if the prototype or simulation results show that there is no static dangerous, but in fact the risk may still exist. In general, we should not use multi-level combinational logic to clock the

28、flip-flop in the PLD design. </p><p>　　Traveling-wave clock clock another popular use of traveling-wave circuit is the clock, that is, the output of a flip-flop used as a clock input of another flip-flop. If

29、 careful design, traveling-wave clock can be the same as the global clock to work reliably. However, the traveling-wave clock made from time to time with the calculation of the circuit becomes very complicated. Line-wave

30、 traveling-wave clock flip-flop of the chain have a greater clock time between the offset and exceed the worst c</p><p>　　Multi-clock system, many system requirements within the same multi-PLD clock. The mos

31、t common example is the two asynchronous interfaces between microprocessors, or microprocessors and asynchronous communication channel interface. As the clock signal between the two requirements to establish and maintain

32、 a certain time, so that the above application from time to time the introduction of additional constraints. They also requested that some asynchronous synchronization signal. </p><p>　　In many applications,

33、 only the synchronization of asynchronous signals is not enough, when the system of two or more non-homologous clock, the data it is difficult to establish and maintain the time to be assured that we will face the comple

34、x matter of time . The best way is to all non-homologous clock synchronization. PLD internal use of the lock loop (PLL or DLL) is a very good, but not all of PLD with a PLL, DLL, and chip PLL with most expensive, so unle

35、ss there are special requirements, the </p><p>　　采用L ED 數碼管的數字顯示以其亮度高、顯示直觀等優點被廣泛應用于智能儀器及家用電器等領域. 本文介紹一種以AT89C52單片機為核心,以共陽極高亮度L ED 數碼管作為顯示器件組成7 位數字顯示的實用多功能電子時鐘的設計,該時鐘可顯示星期、時、分、秒,也可切換為年、月、日顯示,同時具有整點音樂報時及定時鬧鐘等功

36、能,也可作電子秒表使用。</p><p>　　時鐘電路是計算機的心臟, 它控制著計算機的工作節奏就是通過復雜的時序電路完成不同的指令功能的。</p><p>　　時鐘，自從它被發明的那天起，就成為人們生活中必不可少的一種工具，尤其是在現在這個講究效率的年代，時鐘更是在人類生產、生活、學習等多個領域得到廣泛的應用。然而隨著時間的推移，人們不僅對于時鐘精度的要求越來越高，而且對于時鐘功能的要求

37、也越來越多，時鐘已不僅僅是一種用來顯示時間的工具，在很多實際應用中它還需要能夠?qū)崿F(xiàn)更多其它的功能。諸如鬧鐘功能、日歷顯示功能、溫度測量功能、濕度測量功能、電壓測量功能、頻率測量功能、過欠壓報警功能等。鐘表的數字化給人們的生產生活帶來了極大的方便，而且大大地擴展了鐘表原先的報時功能。諸如定時自動報警、按時自動打鈴、時間程序自動控制、定時廣播、自動起閉路燈、定時開關烘箱、通斷動力設備、甚至各種定時電氣的自動啟用等，所有這些，都是以鐘表數字化

38、為基礎的。可以說，設計多功能數字時鐘的意義已不只在于數字時鐘本身，更大的意義在于多功能數字時鐘在許多實時控制系統中的應用。在很多實際應用中，只要對數字時鐘的程序和硬件電路加以一定的修改，便可以得到實時控制的實用系統，從而應用到實際工作與生產中去。因此，研究數字時鐘及擴大其應用，有著非常現實的意義。</p><p>　　隨著人類科技文明的發展，人們對于時鐘的要求在不斷地提高。時鐘已不僅僅被看成一種用來顯示時間的工具

39、，在很多實際應用中它還需要能夠?qū)崿F(xiàn)更多其它的功能。高精度、多功能、小體積、低功耗，是現代時鐘發展的趨勢。在這種趨勢下，時鐘的數字化、多功能化已經成為現代時鐘生產研究的主導設計方向。本文正是基于這種設計方向，以單片機為控制核心，設計制作一個符合指標要求的多功能數字時鐘。</p><p>　　本設計基于單片機技術原理，以單片機芯片AT89C52作為核心控制器，通過硬件電路的制作以及軟件程序的編制，設計制作出一個多功能

40、數字時鐘系統。該時鐘系統主要由時鐘模塊、鬧鐘模塊、環境溫度檢測模塊、液晶顯示模塊、鍵盤控制模塊以及信號提示模塊組成。系統具有簡單清晰的操作界面，能在4V～7V直流電源下正常工作。能夠準確顯示時間（顯示格式為時時：分分：秒秒，24小時制），可隨時進行時間調整，具有鬧鐘時間設置、鬧鐘開/關、止鬧功能，能夠?qū)r鐘所在的環境溫度進行測量并顯示。設計以硬件軟件化為指導思想，充分發揮單片機功能，大部分功能通過軟件編程來實現，電路簡單明了，系統穩定性

41、高。同時，該時鐘系統還具有功耗小、成本低的特點，具有很強的實用性。由于系統所用元器件較少，單片機所被占用的I/O口不多，因此系統具有一定的可擴展性。</p><p>　　時鐘設計無淪是用離散邏輯、可編程邏輯，還是用全定制硅器件實現的任何數字設計，為了成功地操作，可靠的時鐘是非常關鍵的。設計不良的時鐘在極限的溫度、電壓或制造工藝的偏差情況下將導致錯誤的行為，并且調試?yán)щy、花銷很大。在設計FPGA/CPLD時通常采用

42、幾種時鐘類型。時鐘可分為如下四種類型：全局時鐘、門控時鐘、多級邏輯時鐘和波動式時鐘。多時鐘系統能夠包括上述四種時鐘類型的任意組合。</p><p>　　無論采用何種方式，電路中真實的時鐘樹也無法達到假定的理想時鐘，因此我們必須依據理想時鐘，建立一個實際工作時鐘模型來分析電路，這樣才可以使得電路的實際工作效果和預期的一樣。在實際的時鐘模型中，我們要考慮時鐘樹傳播中的偏斜、跳變和絕對垂直的偏差以及其它一些不確定因素。

43、</p><p>　　對于寄存器而言，當時鐘工作沿到來時它的數據端應該已經穩定，這樣才能保證時鐘工作沿采樣到數據的正確性，這段數據的預備時間我們稱之為建立時間（setup time）。數據同樣應該在時鐘工作沿過去后保持一段時間，這段時間稱為保持時間（hold time）。</p><p>　　全局時鐘對于一個設計項目來說，全局時鐘(或同步時鐘)是最簡單和最可預測的時鐘。在PLD/FPGA設

44、計中最好的時鐘方案是：由專用的全局時鐘輸入引腳驅動的單個主時鐘去鐘控設計項目中的每一個觸發器。只要可能就應盡量在設計項目中采用全局時鐘。PLD/FPGA都具有專門的全局時鐘引腳，它直接連到器件中的每一個寄存器。這種全局時鐘提供器件中最短的時鐘到輸出的延時。</p><p>　　門控時鐘在許多應用中，整個設計項目都采用外部的全局時鐘是不可能或不實際的。PLD具有乘積項邏輯陣列時鐘（即時鐘是由邏輯產生的），允許任意函

45、數單獨地鐘控各個觸發器。然而，當你用陣列時鐘時，應仔細地分析時鐘函數，以避免毛刺。</p><p>　　通常用陣列時鐘構成門控時鐘。門控時鐘常常同微處理器接口有關，用地址線去控制寫脈沖。然而，每當用組合函數鐘控觸發器時，通常都存在著門控時鐘。如果符合下述條件，門控時鐘可以象全局時鐘一樣可靠地工作：</p><p>　　驅動時鐘的邏輯必須只包含一個“與”門或一個“或”門。如果采用任何附加邏在

46、某些工作狀態下，會出現競爭產生的毛刺。</p><p>　　邏輯門的一個輸入作為實際的時鐘，而該邏輯門的所有其它輸入必須當成地址或控制線，它們遵守相對于時鐘的建立和保持時間的約束。</p><p>　　多級邏輯時鐘當產生門控時鐘的組合邏輯超過一級(即超過單個的“與”門或“或”門)時，證設計項目的可靠性變得很困難。即使樣機或仿真結果沒有顯示出靜態險象，但實際上仍然可能存在著危險。通常，我們不

47、應該用多級組合邏輯去鐘控PLD設計中的觸發器。</p><p>　　行波時鐘另一種流行的時鐘電路是采用行波時鐘，即一個觸發器的輸出用作另一個觸發器的時鐘輸入。如果仔細地設計，行波時鐘可以象全局時鐘一樣地可靠工作。然而，行波時鐘使得與電路有關的定時計算變得很復雜。行波時鐘在行波鏈上各觸發器的時鐘之間產生較大的時間偏移，并且會超出最壞情況下的建立時間、保持時間和電路中時鐘到輸出的延時，使系統的實際速度下降。</

48、p><p>　　多時鐘系統許多系統要求在同一個PLD內采用多時鐘。最常見的例子是兩個異步微處理器器之間的接口，或微處理器和異步通信通道的接口。由于兩個時鐘信號之間要求一定的建立和保持時間，所以，上述應用引進了附加的定時約束條件。它們也會要求將某些異步信號同步化。</p><p>　　在許多應用中只將異步信號同步化還是不夠的，當系統中有兩個或兩個以上非同源時鐘的時候，數據的建立和保持時間很難得到