外文翻譯--圓錐齒輪的裝配和調整

1、<p><b>　　附錄A：</b></p><p>　　BEVEL GEAR ASSEMBLE AND ADJUSTMENT</p><p>　　1. Follower bevel gear assembly and adjustment</p><p>　　Follower bevel gear and bearing assem

2、bly complex. Assembly, the first beari-ng seat outside the circle painted machine bearing oil into the hole, after the beari-ng inner ring will be pressed into journal so that the Department close to the big </p>

3、<p>　　gear, painted with oil, will take the initiative to gear into the bearing cone, follow-ed by fitted with gaskets to adjust, the former bearing inner ring, gaskets, flanges,</p><p>　　flat washer, a

4、nd finally installed in accordance with the provisions of Slotted Nut </p><p>　　Slotted nut tightening torque. Active degrees bevel gear bearing preload adjustment. Bevel gear assembly quality initiative goo

5、d or bad, the key is to take the initiative to predegree cone gear bearings whether it is suitable to take the initiative to the main bevel gear reducer bearing pretightening same adjustments are an increase or decrease

6、the use of the two frontend between the tapered roller bearing of the adju-sted to achieve the thickness of shim adjustment. Evaluation of active bearing</p><p>　　of the initiative of the bevel gear bearing

7、rotating torque to determine the suitabilityof predegree. Measurement method is that the shell bearings tiger caught in the pin-cers of Taiwan, and with the spring, said hook holes in the flange edge, along the tangent d

8、irection of said pulling spring. Measurement of rotating shaft bevel gear n-eeded to take the initiative to pull the size, take the initiative to rally the necessaryaxis should be consistent with the original, if the pul

9、ling force great</p><p>　　2.Owners, the driven bevel gear meshing with the meshing clearance checks </p><p>　　imprinted with the adjustment.</p><p>　　Lord, the driven bevel gear mes

10、hing of the check mark. Driven bevel gear b-earing predegree, after a good tune, good tune to take the initiative into the main </p><p>　　bevel gear reducer shell assembly. Attention when installed in the ap

11、propriate place between the two joints to adjust the thickness of the gasket, in accordance with the provisions of the fixed bolt tightening torque, and then coloring in the circumstan-ces, nonload the main bevel gear me

12、shing driven situation. Inspection, the first driv-en bevel gear in 120 degrees of adjacent three teeth each from 2-3 in the tooth su-rface coated with thin uniform Hongdan oil, and then to the driven bevel gear</p>

13、;<p>　　correct. Imprinted mesh design of the factory have a clearly defined, you can refer to the use of manuals, Western engagement in the teeth located in the central recta-ngle Xiaoduan bias away from the edge

14、of Xiaoduan 2 4mm, high gear is located </p><p>　　in the central direction of bias from the tooth tip 0.8 -1.6mm, mesh gear is negative imprinting seek the same adjustment, if there are contradictions betwee

15、n the two should be a positive engagement, but the negative to ensure that the principle can work properly, otherwise there should be gear grinding or replacement. Lord, the d-riven bevel gear meshing blot, mesh gap adju

16、stment. Lord, the driven bevel gear </p><p>　　meshing and mesh imprinting of the adjustment is the use of space to change the </p><p>　　center distance of two gear assembly to achieve in changin

17、g the mating contacts at Western will also change in space, they are interrelated and mutually contradictory, in the adjustment often occur when the value of space to meet the requirements,</p><p>　　the prov

18、isions do not conform to Western society. Tooth surface as a result of Western contact with the good or bad, is to determine tooth contact area, the assembly centers, such as distance and profile is an important basis to

19、 meet the requirements.Therefore, when imprinted with the meshing engagement gap adjustment of disputes,conflicts mesh imprinting is the major aspects of Western engagement should ensurethat the main gap may be more appr

20、opriate to enlarge, but not more than its limit,adju</p><p>　　imprinting of the big-time, should be driven bevel gear bevel gear to take the initiative by the disturbance, if the meshing of space, therefore

21、too small bevel gear can take the initiative to move out, when in contact with Western follower Xiaoduan </p><p>　　bevel gear, the driven bevel gears should be adjusted to take the initiative to leave the be

22、vel gear. If the gap arising from the meshing is too large, can take the initiative to move inward bevel gear. When exposed to Western in the top of the drivenbevel gear, it will take the initiative to adjust the bevel g

23、ear to the bevel gear driven by the disturbance, so the meshing of smaller gap can be adjusted from the dynamic relocation of bevel gears, when the driven cone in contact with Western when</p><p>　　圓錐齒輪的裝配和調

24、整 　</p><p>　　1.從動圓錐齒輪的裝配與調整 　　 　　</p><p>　　從動圓錐齒輪的裝復。將軸承內圈壓到中間軸軸頸上，涂上機油，將鉚好從動齒輪的中間軸裝入主傳動器中殼體內，將軸承外圈壓入側蓋，先按分解記錄的調整墊片數量分別用螺栓套在左右側蓋上連側蓋一起裝上，注意側蓋與主減速器接合面處應加密封墊，靠近從動圓錐齒輪一側調整墊片可適當厚些，以防下一步調齒輪嚙合問隙時齒隙過小而

25、卡住，按規定力矩擰緊左右側蓋固定螺栓。從動圓錐齒輪軸承預緊度的調整。從動圓錐齒輪軸承預緊度的檢查方法，用百分表測量，測量時將百分表固定于主減速器殼上，表觸頭抵住從動錐齒輪的背面，左右撬動從動錐齒輪，表上所指最大與最小數值之差即為軸向移動量，一般應不大于0．05mm，最大不得超過O．10mm。檢查時，如果軸向間隙值大于規定，則減少任意一邊側蓋下調整墊片的厚度，如若軸向間隙小于規定值或轉動從動錐齒輪阻滯不靈活，則應增加任一邊測蓋下調整墊片的

26、厚度，直至檢查合格為止。 　　 </p><p>　　2.主、從動錐齒輪嚙合印跡與嚙合間隙檢查與調整 　</p><p>　　主、從動錐齒輪嚙合印痕的檢查。從動錐齒輪軸承預緊度調好之后，把調好的主動錐齒輪總成裝入主減速殼內。注意裝時，在兩接合面間放適當厚度的調整墊片，用螺栓固定并按規定力矩擰緊，然后用涂色法在無負荷情況下檢查主從動錐齒輪嚙合情況。檢查時，首先在從動錐齒輪相鄰120度三處每處

27、取2-3輪齒，在齒面薄而均勻的涂上紅丹油，然后對從動錐齒輪略施阻力，轉動主動錐齒輪帶動從動錐齒輪轉幾圈，然后停止下來，觀察從動錐齒輪上壓出的印跡，是否符合原廠要求。主、從動錐齒輪嚙合間隙的檢查方法。檢查時，首先將百分表座固定，使百分表觸頭垂直于從動錐齒輪大端的凸面上抵住，表針對零，手握主動錐齒輪不動，另一手輕輕來回推動從動錐齒輪，表上所指示數即為其嚙合問隙值。正確的嚙合印跡。嚙合印跡各制造廠設計時都有明確規定，可以參閱使用說明書，嚙合印