文獻翻譯--溫室監控系統的設計和實現基于gsm和射頻技術

1、<p>　　2215單詞，1.2萬英文字符，3540漢字</p><p>　　出處：Zhao X, Zheng X, Chen D, et al. The design and implementation of the greenhouse monitoring system based on GSM and RF technologies[C]// International Conference

2、on Computational Problem-Solving. IEEE, 2013.</p><p>　　The Design and Implementation of the Greenhouse</p><p>　　Monitoring System Based on GSM and RF Technologies</p><p>　　X Zhao，X

3、Zheng，C Duan，Z Chen</p><p><b>　　Abstract</b></p><p>　　According to the characteristics of small and medium-sized greenhouse environmental monitoring, this paper proposes a solution t

4、o remote greenhouse environmental monitoring which is based on GSM technology and RF. The system constitutes the regional environmental information monitoring network and close communication platform based on radio frequ

5、ency. Combined with the remote communication technology based on GSM networks, the system implements small and medium-sized greenhouse environmental mon</p><p>　　structure and software workflow chart. It sho

6、ws that the system is stable, reliable, and it’s able to achieve real-time monitoring of greenhouse environment.</p><p>　　Keywords: RF; sink node; wireless communication; greenhouse environmental monitoring;

7、 wireless sensor network</p><p>　　I. Introduction</p><p>　　In recent years, with the rapid development of the greenhouse industry, the greenhouse environment control technology is of higher requ

8、irements because of how to obtain accurate and reliable information, as described by [1-2]. In China, most of existing greenhouse control systems uses wired communication, which inevitably faces with wiring problem. The

9、wiring problem includes mass construction, high cost, installation and maintenance difficulties and that a broken node is likely to cause the ent</p><p>　　Through literature review, it is found that some dom

10、estic scholars utilized wireless sensor network technology in [3-4]; while some scholars used microprocessors with Zigbee technology and multi-sensor fusion technology to design</p><p>　　greenhouse monitorin

11、g sensor nodes, as in [5]; And some scholars utilized interventional Internet or Intranet way to achieve remote monitoring in [6]; Ref.[2] presented there were also some scholars who used GSM technology combined with wir

12、eless sensor network technology to design greenhouse environment monitoring system. These projects are relatively good designs, but their hardware designs are</p><p>　　complex and of high cost, especially in

13、 small greenhouse monitoring applications, the cost performance is not high. In view of this, I integrate GSM wireless communication technology and radio frequency (RF) technology, and make the use of the existing GSM ne

14、twork terminal - GSM module for remote data transmission application conditions merging with the RF technology. Eventually, I put forward a cost-effective solution to small and medium-sized greenhouse monitoring. The sys

15、tem based on RF techn</p><p>　　short distances and requiring high reliability.</p><p>　　II. System Architecture</p><p>　　The greenhouse monitoring system integrates the RF technolog

16、y and GSM technology and applies the RF technology to the design of wireless monitoring nodes and sink nodes. Through initializing the RF module PTR4000 and matching address, the data collected by monitoring nodes is del

17、ivered to the sink nodes which deal with the received data. The processed data is uploaded to the specified server by the remote communication terminal (GTM900-C) based on GSM network. The data transmission between monit

18、</p><p>　　monitoring node and sink node form a local area network and the data is sent to the specified server by a common GSM module, which prevents the uploading of single data, thus greatly reducing syste

19、m development costs.</p><p>　　The monitoring system is mainly composed of three parts: wireless monitoring nodes, sink nodes, and remote communications terminal based on GSM network. The system architecture

20、is shown in Fig. 1.</p><p>　　Monitoring nodes are used to collect parameters of greenhouse environment such as temperature, humidity and so on. Sink node is monitoring data collector and sorter, which is res

21、ponsible for monitoring communications between the region and the server. Sink node receives the data sent by motoring nodes, analyzes it to make a decision, and then remotely delivers the processed data through GSM modu

22、le. Each motoring node is equipped with wireless communication RF module so that the parameters of gre</p><p>　　module which is used to achieve communication between sink node and remote sever.</p>&l

23、t;p>　　Figure 1 The system architecture</p><p>　　III. The Hardware Design </p><p>　　A. The Hardware Design of Monitoring Nodes</p><p>　　Monitoring nodes use ATmega16A as MCU, and

24、 utilize PTR4000 as the RF module. MCU initializes PTR4000 to select the working way of monitoring nodes and match communication address. After monitoring nodes receive the instructions sent by sink node, MCU sends the d

25、ata collected by sensors to specified sink node through PTR4000.</p><p>　　As shown in Fig. 2, the whole hardware system involves power module, microprocessor module, RF module and data acquisition modules.&l

26、t;/p><p>　　Figure 2 The monitoring node hardware circuits diagram</p><p>　　In the design, the high-speed and low-power data transmission module PTR4000 based on one-chip wireless transceiver chip

27、nRF2401A which is issued by Nordic is selected as wireless communication RF module. Ref. [7-8] presented the chip’s characteristics. It is of low power and its operating voltage is 1.9V~3.6V. A 2.4GHz antenna is built in

28、 the chip and it takes global open 2.4GHz band, which establishes 128 channels (each channel bandwidth is 1MHz) between 2400MHz and 2527MHz and the switching t</p><p>　　detection is built in the chip so that

29、 error rate can be reduced without increasing the difficulty of programming. The chip supports multi-point communication with efficient GMSK modulation and the maximum transfer rate is up to 1Mbit/s. The module address c

30、an be set by software so that the data can be output only if the address of the local machine is received. The data collecting module is mainly responsible for collecting parameters of greenhouse environment and we can&l

31、t;/p><p>　　configure a variety of temperature and humidity sensors required by monitoring greenhouse environment according to the requirements. (Attention: DS18B20 temperature sensor is deployed in the test.) I

32、n terms of microprocessor, I select the</p><p>　　low-power CMOS microcontroller ATmega16A based on enhanced AVR RISC architecture issued by ATMEL, which is used to control the data collecting module and the

33、RF module. As to power module, solar cells are selected as the power system as in [9]. The entire solar cell system is composed of solar panels, solar charge controller and battery constituting. As the power consumption

34、of monitoring nodes is low, the power system can ensure the normal operation of the monitoring network.</p><p>　　B. The Hardware Design of Sink Nodes</p><p>　　Sink node uses ATmega16A as MCU, ut

35、ilizes PTR4000 as the RF module and selects GTM900-C as the GSM module. Through controlling the RF module and the GSM module, MCU uploads the data information to the specialized severs. Firstly, sink node sends instructi

36、ons. Then, corresponding monitoring nodes receive instructions and transmit the data collected by sensors to the sink node through PTR4000. And then the RF module PTR4000 in the sink node receives the data and sends the

37、data processed by MCU to </p><p>　　Fig. 3 shows the entire hardware system including the power module, the microprocessor module, the RF module, the keyboard and the GSM remote communication module.</p>

38、;<p>　　Figure 3 The sink node hardware circuits diagram</p><p>　　In the design, the microcontroller ATmega16A is selected as the microprocessor to control the RF module and the GSM module instantly a

39、nd figure out the gathered parameters of greenhouse environment. And PTR4000 is used as the wireless communication RF module to receive the data information delivered by respective monitoring nodes. I choose the GTM900-C

40、 produced by HuaWei as the GSM</p><p>　　emote communication module to upload the processed data to the specialized sever. As described by [10], the GTM900-C wireless module is a two-band GSM / GPRS wireless

41、module which supports standard AT commands and enhances AT commands and provides plenty of short messages, voice and data services and other functions. It is an ideal solution for a variety of applications such as high-s

42、peed data transmission.</p><p>　　In terms of the power module, solar cells are selected as the power system as in [9].</p><p>　　IV. The Design Of Communication Protocol</p><p>　　A.

43、The design of PTR4000 communication protocol</p><p>　　When using PTR4000 for wireless data communication, we do not need Manchester coding and are easy to program and apply. As long as we follow the configur

44、ation instructions (seeing Table I), what we need to do is just to write the hardware address of the nodes and sink nodes, data length and the rest of the configuration word to the status word. In this system, the sink c

45、ode address is 0x3a3b3c3d3e and the monitoring node addresses are 0x1a1b1c1d1e, 0x2a2b2c2d2e.</p><p>　　Both nodes and sink node are 16 parity bits. The parity bit is enabled, single, burst mode, 1Mb/s, cryst

46、al frequency 16MHZ, operating frequency 2400MHZ and the lowest bit 0 is emission (it can be temporarily configured when needing to receive data temporarily).</p><p>　　TABLE 1 PTR4000C On Figuration Keyword

47、List</p><p>　　B. The design of GTM900 communication protocol</p><p>　　HUAWEI GTM900-C wireless module is a two band GSM/GPRS wireless module, it supports standard AT commands, and enhances the A

48、T command, and provides a rich text messages, voice and data services, and other functions, is the ideal solution for various applications such as high-speed data transfer. GTM900-C integrates TCP/IP protocol and uses th

49、e expansion of the internal the AT command. According to the manual of the GTM900-C wireless module AT commands, users need only send the compiled AT comman</p><p>　　Command "AT" / / test GTM900-C

50、is ready;</p><p>　　Return OK;</p><p>　　Command "AT + CMGF = 1" / / set to send data in the form of text;</p><p>　　Return OK;</p><p>　　Command "AT + CMGS

51、= '11 phone number' / / connect to the server, set the server number;</p><p>　　Return ">";</p><p>　　Type the contents and sent them by the means of “Ctrl+Z";</p>

52、<p>　　Return OK;</p><p>　　V. The Software Design</p><p>　　A. The software design of monitoring node</p><p>　　The key of the design of Monitoring nodes of process is communicat

53、ion of microcontroller and PTR4000 module. Its workflow chart is shown in Fig. 4. When Monitoring node is electrified, sensor and RF module PTR4000 will initialize, and then PTR4000 to enter configuration mode. We based

54、on PTR4000 to write configuration, so that it is in receiving mode. Until PTR4000 receives the sink node command, the monitoring node will start to work. After the completion of the acquisition data, RF module PTR4</p

55、><p>　　sent to the sink node. After sending, RF module PTR4000 will be into receiving mode and wait for the arrival of the next sink node command.</p><p>　　Figure 4 The workflow chart of monitorin

56、g nodes.</p><p>　　B. The software design of sink node</p><p>　　It’s the key to SCM, GTM900 module and PTR4000 module communication. Its workflow chart is shown in Fig. 5.</p><p>　　F

57、igure 5 The workflow chart of sink node.</p><p>　　After powered on, the sink node device initializes and sets the server address (i.e., input 11 phone number). Then, RF module PTR4000 is into sleeping mode

58、and Microcontroller start timer. After the prescribed time, we make PTR4000 at the sending mode via writing configuration word to RF module. At this time, sink node sends commands to the monitoring node. The monitoring n

59、ode starts to collect relevant data and information in greenhouse, and sends the collected data to the sink node. Sink node </p><p>　　VI. The Experimental Results </p><p>　　After establishing th

60、e greenhouse environment monitoring system, test experiment was carried out in the open area and indoor to test the transmission distance and the BER of the system. The open experiment was selected on the school track an

61、d field. Through comparing the sending data with receiving data, We found that the error-free data transmission distance was up to 50 m, more than the distance we didn’t receive any data; The indoor test was selected in

62、YiFu building study room. In an interva</p><p>　　In the process of the experiment, we found that the received data is either right or we didn’t receive any data; there is no error rate of the problem.</p&

63、gt;<p>　　VII. Conclusions</p><p>　　According to the characteristics of the greenhouse environmental monitoring, the article puts forward a kind of design scheme of greenhouse environmental information

64、 remote monitoring system based on RF technology and GSM communication technology. And it introduces the overall structure of the system and the software and hardware design method of each part in detail. It provides a c

65、ost-effective solution for the small and medium-sized greenhouse monitoring.</p><p>　　References</p><p>　　[1] Yang Wei, Li Min-zan, and Wang Xiu, “Status Quo and Progress of Data Transmission an

66、d Communication Technology in Field Information Acquisition,” Transactions of the CSAE, 2008, vol. 24, pp.297-301.</p><p>　　[2] Yang Jing, Bai Bao-liang and Li Han-dong, “Design of Greenhouse Environment Mon

67、itoring System Based on GSM and WSN,” Journal of Anhui Agricultural Sciences, 2012, vol. 40, pp. 2497-2498, 2556.</p><p>　　[3] Gao Feng, Yu Li, Zhang Wen-an, Xu Qing-xiang and Yu Li-jie, “Research and Design

68、 of Crop Water Status Monitoring System Based on Wireless Sensor Networks,” Transactions of the CSAE, 2009, vol.25, pp. 107-112.</p><p>　　[4] Tang Yi-feng, Chen Xin-hua, Feng Hui and Luo Bin, “Design of Wire

69、less Sensor Network Node for Environmental Monitoring in Greenhouse,” Journal of Hunan Agricultural Sciences, 2010, pp. 146-148, 151.</p><p>　　[5] Wang Dong, “Research and Realization Control System of Green

70、house Environmental Based on Muti-Sensor Fusion,” Thesis for Master Degree, Northwest A&F University, 2012.</p><p>　　[6] Wang Yi and Zhou Jie, “Design and Realization of Remote Monitoring System of Green

71、house Environment by Using GSM,” Modern Electronics Technique, 2008, vol. 31, pp. 151-154.</p><p>　　[7] Liao Ping and Qiao Gang, “Short Range Wireless Communication System from One to Many Based on NRF2401,”

72、 Modern Electronics Technique, 2006, vol. 29, pp. 18-20.</p><p>　　[8] Zhang Chong, Lin Xiao and Liu Ping-jian, “Design for Remote and High Speed Wireless Communication Based on NRF2401,” International Ele

73、ctronic Elements, 2007, vol. 14, pp. 84-86.</p><p>　　[9] Zhu Ying-li, Song Jing-jiang and Dong Fu-zhou, “Applications of Wireless Sensor Network in the Agriculture Environment Monitoring,” Procedia Engineeri

74、ng, 2011, vol. 16, pp. 608-614[Elsevier Ltd. Selection, in the press, 2010].</p><p>　　[10] Xian Jin-long and Yang Yang, “Study and Implication of Remote Grain Situation Measurement and Control Based on GTM90

75、0,” Journal of Henan University of Technology ( Natural Science Edition), 2011, vol.32, pp. 79-82.</p><p>　　溫室監控系統的設計和實現基于GSM和射頻技術</p><p><b>　　摘要</b></p><p>　　根據中小溫室環境監測

76、的特點，提出了一種基于GSM和射頻技術來解決遠程溫室環境監測。系統構成了區域環境信息監測網絡和基于射頻的密切溝通平臺。基于GSM網絡的遠程通信技術,該系統實現了中小溫室環境監測。使用ATmega16A、低功耗芯片PTR4000和華為無線模塊GTM900-C設計系統的監測節點和水槽節點，本文給出了系統的硬件結構和軟件流程圖表。它表明，系統是穩定的、可靠的，能夠?qū)崿F(xiàn)對溫室環境的實時監控。</p><p>　　關鍵詞：

77、射頻 水槽節點 無線通信 溫室環境監測的無線傳感器網絡</p><p><b>　　1 介紹</b></p><p>　　近年來，隨著溫室產業的快速發展，考慮到如何獲得準確、可靠的信息，對溫室環境控制技術需求越來越高，就像[1-2]中所述。在中國，大多數現有的溫室控制系統使用有線通信，這不可避免地面臨著布線的問題。布線的問題包括質量建設、高成本、安裝、維護困難

78、和破碎的節點可能會導致整個系統的工作。使用無線通信是解決這些問題的最好方法。無線通信不需要布線、成本低、易于維護，還可以增加或減少測量任意節點。因此，它具有良好的應用前景。</p><p>　　通過文獻綜述，發現一些國內學者利用無線傳感器網絡技術[3-4]，使用微處理器和無線局域網技術和多傳感器融合技術設計溫室監測傳感器節點，如[5]；另一些學者利用介入互聯網或局域網方式來達到遠程監控[6]；在Ref.[2]中也

79、有一些學者提出了使用GSM技術結合無線傳感器網絡技術設計的溫室環境監測系統。這些項目是相對良好的設計，但是他們的硬件設計是復雜而且高成本的，特別是在小型溫室監控應用程序中，性價比不高。針對這一點，我將通過GSM無線通訊技術和射頻(RF)技術，并使用現有的GSM網絡終端——GSM模塊遠程數據傳輸應用程序與射頻技術合并；最后，我提出了一個符合成本效益的中小溫室監控系統的解決方案。基于射頻技術的系統構成了區域環境信息監測網絡，結合GSM遠程通

80、信技術，實現了小溫室環境遠程的成功監控。實驗結果表明，該系統特別適合數據采集系統和短距離要求，可靠性高。</p><p><b>　　2 系統架構</b></p><p>　　溫室監控系統集成了射頻技術和GSM技術，射頻技術適用于無線監測節點和水槽節點的設計。通過射頻模塊初始化PTR4000和匹配地址，收集到的數據通過監測節點交付給水槽節點處理，處理過的數據上傳到指

81、定服務器，即基于GSM網絡遠程通信終端(GTM900-C)。監控節點之間的數據傳輸降低了功率，傳輸速度變快，除了每個監測節點和匯聚節點形成一個局域網絡外，數據由一個共同的GSM模塊發送到指定的服務器，從而防止單一數據的上傳，從而大大降低了系統的開發成本。</p><p>　　監控系統主要由三部分組成：無線監測節點，水池節點，基于GSM網絡的遠程通信終端。系統架構圖1所示。</p><p>

82、　　監控節點用于收集溫室環境參數，如溫度、濕度等；水槽節點監測數據收集器和分選機，負責監控區域和服務器之間的通信。匯聚節點接收監控節點發送的數據，分析并做出決定，然后通過GSM模塊遠程加工數據。每個監控節點配備無線通信射頻模塊用于溫室環境參數的傳輸。水槽節點不僅配備了無線通信射頻模塊，而且配置了GSM通信模塊用于實現匯聚節點和遠程服務器之間的通信。</p><p><b>　　圖1 系統架構</

83、b></p><p><b>　　3 硬件設計</b></p><p>　　3.1 監測節點的硬件設計</p><p>　　監控節點使用ATmega16A單片機，利用PTR4000射頻模塊。單片機初始化PTR4000、選擇監測節點的工作方式和與通信地址相匹配，之后監測節點接收匯聚節點發送的指令，單片機通過PTR4000指定將傳感器采集的

84、數據發送給匯聚節點。</p><p>　　如圖2所示，整個硬件系統包括電源模塊、微處理器模塊、射頻模塊和數據采集模塊。</p><p>　　圖2 監控節點硬件電路框圖</p><p>　　在設計高速、低功耗數據傳輸模塊PTR4000的上，選擇基于單芯片的無線收發芯片nRF2401A作為無線通信射頻模塊。Ref. [7-8] 介紹了芯片的特點，低功率，其工作電壓為1

85、.9 v ~ 3.6 v。2.4 GHz天線是建立在全球開放的2.4 GHz芯片上，它建立了128個頻道(每個通道帶寬1 MHz)2400 MHz和2527兆赫之間通道之間的切換時間小于200ms。硬件CRC錯誤檢測是建立在芯片內，這樣可以減少出錯率而且不增加編程的難度。芯片支持多點有效溝通，實現GMSK調制和最大傳輸速率為1 Mbit/s。模塊地址可以通過軟件設置，數據只有在接收到本地機器的地址后才能輸出。數據采集模塊主要負責收集溫室

86、環境參數，我們可以根據需求配置各種所需的溫度和濕度傳感器監測溫室環境。（注意：DS18B20溫度傳感器部署在測試端）。對于微處理器，我選擇低功耗的CMOS單片機ATmega16A，基于增強型ATMEL AVR RISC體系結構，用于控制數據采集模塊和射頻模塊。電源模塊，我選擇太陽能電池作為電力系統[9]，整個太陽能電池系統是由太陽能電池板、太陽能充電控制器和電池組成。監控節點的功</p><p>　　3.2 水槽

87、節點的硬件設計</p><p>　　水槽節點使用ATmega16A作為單片機，利用PTR4000射頻模塊并選擇GTM900-C為核心的GSM模塊。通過控制射頻模塊和GSM模塊，單片機作為上傳數據信息的專用服務器。首先，水池節點發送指令；然后，接收指令并傳送相應的監測節點收集到的數據到傳感器和PTR4000水槽節點；接著，由單片機控制PTR4000 RF模塊和GTM900為核心的GSM模塊，將水槽節點接收到的數據發

88、送出去；最后，GTM900通過使用命令上傳數據信息至預設服務器。</p><p>　　圖3顯示了整個硬件系統，包括電源模塊、微處理器模塊、射頻模塊、鍵盤和GSM遠程通信模塊。</p><p>　　圖3 水槽節點硬件電路框圖</p><p>　　在設計中，單片機ATmega16A作為微處理器來控制射頻模塊和GSM模塊，并立即計算出聚集的溫室環境參數。PTR4000作為

89、無線通信射頻模塊，由各自監控節點接收數據信息。我選擇華為生產的以GTM900-C為核心的GSM通信模塊，將處理過的數據上傳到專門的服務器。像[10]所述，GTM900-C無線模塊是一個雙波段GSM/GPRS無線模塊，支持標準AT指令，增強AT指令的可讀性，提供了大量的短信、語音、數據服務和其他功能，這為各種應用例如高速數據傳輸?shù)忍岢隽艘粋€理想的解決方案。電源模塊則選擇太陽能電池作為電力系統[9]。</p><p>

90、;　　4 通信協議的設計</p><p>　　4.1 PTR4000通信協議的設計</p><p>　　當使用PTR4000無線數據通信時，我們不需要進行曼徹斯特編碼，這樣更易于程序的編寫和應用擴展。只要我們遵循配置說明（見表1），我們需要做的就是寫硬件地址節點、水槽節點、數據長度和其余的配置字的狀態。在此系統中，水槽代碼地址是0 x3a3b3c3d3e，監控節點地址是0 x1a1b1c

91、1d1e 0 x2a2b2c2d2e。節點和匯聚節點都是16個奇偶校驗位。啟用校驗位，單邊的，爆發模式，1 Mb/s，晶體頻率為16兆赫，工作頻率2400 MHz和最低0排放（當需要臨時接收數據時，它可以暫時配置）。</p><p>　　表1 PTR4000C關鍵字列表</p><p>　　4.2 GTM900通信協議的設計</p><p>　　華為GTM900-

92、C無線模塊包含GSM/GPRS兩個無線模塊，它支持AT指令，增強AT指令的應用，并提供了文本消息、語音、數據服務和其他功能，是高速數據傳輸?shù)雀鞣N應用程序的理想解決方案。GTM900-C集成了TCP / IP協議，并且內部使用AT命令進行編程。根據GTM900-C無線模塊手冊提供的命令，用戶只需要通過單片機和串行端口編譯命令發送到無線模塊GTM900-C，然后它可以實現初始化和數據發送。其主要步驟如下：</p><p&

93、gt;　　Command "AT" / / 測試 GTM900-C準備就緒；</p><p>　　Return OK;</p><p>　　Command "AT + CMGF = 1" / /以文本的形式發送數據；</p><p>　　Return OK;</p><

94、;p>　　Command "AT + CMGS = '11 phone number' / /連接服務器，并設置號碼；</p><p>　　Return ">";</p><p>　　Type the contents and sent them by the means of “Ctrl+Z";</p>&

95、lt;p>　　Return OK;</p><p><b>　　5 軟件設計 </b></p><p>　　5.1 監控節點的軟件設計</p><p>　　監控節點設計過程的關鍵是單片機和PTR4000模塊之間的通信，其工作流程圖表如圖4。當監測節點帶電時，將初始化傳感器和射頻模塊PTR4000，然后PTR4000進入配置模式?；赑T

96、R4000所寫的配置，其處于接收模式，直到PTR4000收到水槽節點的命令，監控節點將開始工作。收集數據完成后，射頻模塊PTR4000進入交付模式，并將收集到的數據發送到匯聚節點。發送完成后，射頻模塊PTR4000又將進入接收模式，等待下一個水槽節點的命令的到來。</p><p>　　圖4 監測節點的工作流程圖表</p><p>　　5.2 匯聚節點的軟件設計</p>&l

97、t;p>　　這是GTM900模塊和PTR4000模塊通信供應鏈管理的關鍵。其工作流程圖表圖5所示。</p><p>　　圖5 水槽節點的工作流程圖表</p><p>　　系統啟動后，水槽節點設備初始化并設置服務器地址(即輸入電話號碼)。然后，射頻模塊PTR4000進入睡眠狀態，單片機開始計時。通過規定的時間后，我們通過PTR4000射頻模塊發送模式配置字。在這個時候，水槽節點發送命

98、令至監視節點，監測節點在溫室開始收集相關數據和信息，并將收集到的數據發送給匯聚節點，匯聚節點進行數據的接收和處理。在微處理器的控制下，通過GSM模塊將結果發送到服務器(GTM900-C)?，F(xiàn)在，我們意識到時間采集的功能，中斷返回后，系統將再次回到待機模式，等待下一個采樣周期的到來。</p><p><b>　　6 實驗結果</b></p><p>　　建立好溫室環境

99、監測系統后，我們進行了開放地區和室內地區的測試實驗，主要測試系統的傳輸距離和誤碼率。開放實驗是選擇在學校田徑場，通過比較發送數據和接收數據，我們發現錯誤數據傳輸距離在50米，以上的距離我們沒有收到任何數據；室內測試被選中在逸夫樓自習室，在間隔的墻壁兩邊，通過比較發送數據和接收數據，我們發現錯誤數據傳輸距離達到13米，以上的距離我們也沒有收到任何數據。</p><p>　　在實驗的過程中，我們發現接收的數據是正確的

100、或沒有收到任何數據，錯誤率為零。</p><p><b>　　7 結論</b></p><p>　　根據溫室環境監測的特點，本文提出了一種設計方案，是基于射頻技術和GSM通信技術的溫室環境信息遠程監控系統，這里介紹了系統的總體結構和各部分軟件和硬件的設計方法。它提供了一個在中小溫室監控條件下具有成本效益的解決方案。</p><p><b

101、>　　參考文獻</b></p><p>　　[1] Yang Wei, Li Min-zan, and Wang Xiu, “數據傳輸和通信技術領域信息采集的進展和現狀” , 農業工程學報, 2008,卷24, pp.297-301.</p><p>　　[2] Yang Jing, Bai Bao-liang and Li Han-dong, “基于GSM和傳感器網絡的